Bose® PowerShare PS602 - Commercial Power Amplifier with DSP, 2Ch., 600W @ 70V With Independent Output Control
OUR INNOVATIONS. YOUR EMOTIONS
About the Bose® PowerShare PS602
You Choose How Much Power Each Zone Gets
For example, you could mount four Bose FreeSpace® DS 16F speakers in a small stock room, and send them 64 of the PS602's 600 watts, then surface-mount more than a dozen Bose FreeSpace DS 100SE speakers around your much larger retail floor and send them the rest. DFL™ (Dual Feedback Loop) System continuously monitors and controls current and voltage delivered to each load for improved performance and protection for your speakers.
Part of a Customizable Bose Sound Solution
- Smart PowerShare technology gives you total control of output
- Asymmetrical power output lets you decide how much of the amplifier's 600 total watts to send to each zone
- Each channel can be configured for low impedance (4-8 ohms) or high impedance (70/100V)
- Two unbalanced mono RCA inputs and two balanced Phoenix-style Euroblock inputs
- Two Phoenix-style Euroblock speaker-level outputs
- PowerShare Editor software offers control of EQ, mixing, crossover, limiters, delay, and more (via rear-panel USB Type-B port)
- DFL™ (Dual Feedback Loop) System continuously monitors and controls current and voltage
- Rear-panel dip switches offer additional control over settings
- Individual Channel 1 & 2 EQ dials let you set the output to match select Bose Professional speaker models
- Auto-standby reduces power consumption when amplifier is not in use
- RJ-45 connection for CC-1 ControlCenter volume control
- 19"W x 1-3/4"H x 16-5/16"D
- Weight: 12.2 lbs.
- Warranty: 1 year
What's in the Box:
- 79" Power cord (3-pin IEC)
- Two 3-Pin Euroblock (Phoenix) connectors
- Two 2-Pin Euroblock connectors (green)
- One 2-Pin Euroblock connector (black)
- Owner's manual
Inputs: The PS602 has 2 input channels. Two 3-pin Euroblock connectors provided for balanced and unbalanced signals, as well as a set of dual RCAs with the left input going to Channel 1 and the right input going to Channel 2. Both input types are available simultaneously as long as the same channel isn't using both.
Outputs: Two 2-pin Euroblock connectors are provided for the output channels. These can be run as high-impedance 70/100 volt outputs or low-impedance 4/8Ω outputs. Like the inputs, both types of outputs can be used simultaneously except by the same channel, providing exceptional flexibility. Each output channel has its own Output Attenuation dial that can go from 0 dB attenuation to fully muted when turned completely counter-clockwise.
PowerShare Technology: Bose's patented PowerShare technology allows the total 600 watts of power to be shared asymmetrically across all channels. Since each channel is capable of outputting the full 600 watts, this technology allots more power to the speakers that need it when they need it.
DFL System: The Dual Feedback Loop system improves performance and reliability through continuous monitoring and control of both the current and voltage delivered to each output load. This combination provides improved linearity and lower distortion while protecting the speakers.
Configuration: Configuring the PS602 can be done from either the rear-panel switches or with Bose's PowerShare Editor software when connected to a PC via the rear-panel USB type-B jack (Mac not supported). The PowerShare Editor software offers real-time selection and control of Bose loudspeaker EQs, 9-band parametric EQs, mixing, crossovers, limiters, delay, mute, and output polarity. For basic setups without a PC, the rear-panel has both a 6-selector DIP switch matrix as well as selector dials for each channel that offer 10 preset Bose speaker EQ settings, based on specific models of Bose speakers. The included preset selections are: Flat, DS16, DS40, DS100, FS3B, 402, 802, MA12EX, RMU105, and RMU108. The DIP switch matrix provides the following options:
- Auto Standby: On/Off. If enabled (on), the unit will automatically go into standby mode if it doesn't receive a signal for 20 minutes. If in standby mode, the amp will "wake up" when a signal is present.
- Global Out: 70V or 100V. This setting determines if the amp will be used in a 70 or 100-volt configuration.
- Config: Rear or Software. Determines which method will be used to configure the amp, either with the rear-panel switches or the PowerShare Editor software via a connected PC.
- Sensitivity: 4 dBu or 12 dB. This is used to set the input sensitivity for the Euroblock line-level inputs. If using the unbalanced RCA inputs, the 4 dB setting gives an input sensitivity of -10 dBV while the 12 dB setting gives an input sensitivity of -2 dBV.
- Output 1: Hi Z/Low Z. Determines if Output 1 will be used as a high-impedance 70/100 volt output or a 4/8Ω load.
- Output 2: Hi Z/Low Z. Determines if Output 2 will be used as a high-impedance 70/100 volt output or a 4/8Ω load.
Mute: A 2-pin Euroblock connector is provided for remote muting of the output signal. This is a normally open circuit that mutes if closed, but the polarity can be changed using the PowerShare Editor software.
Front Panel: The amp's front panel contains the main power switch along with 5 LED indicators.
- Power LED: Solid green indicates the amp is on. Blinking green indicates the unit is in lower-power mode. Solid amber shows an over-temperature fault, and solid red indicates a power supply fault.
- Signal LEDs: Both input channels have a Signal LED that lights solid green with a typical input signal. This will change to amber when the signal level gets close to clipping and then to red if it does clip.
- Limit LEDs: Each output channel has a Limit LED that lights amber when the amplifier is limiting the corresponding output due to exceeding the loudspeaker's Peak or RMS power limits. If the sum of the amplifier outputs exceeds 600 watts, then it will limit all outputs equally with both LEDs showing limiting simultaneously. These LEDs will blink red when all outputs are muted from the rear-panel mute connector. Both LEDs will light solid red when there is an amplifier fault or a power supply fault.
- Power: 2 x 300 W
- Maximum Power per Channel: 600 W @ 4-8Ω, 70/100 V
- Frequency Response: 20 Hz - 20 kHz for 4-8Ω, same for 70/100 V except with a 50 Hz high-pass filter
- THD+N: < 0.04 % (1 kHz, 4-8 Ω, 70/100 V)
- Channel Separation: >85 dB @ 1 kHz, > 65 dB @ 20 kHz
- Signal to Noise Ratio: 100 dB
- Audio Inputs:
- Input Channels: 2 Unbalanced, 2 balanced
- Connectors: 2 RCAs, 3-pin Euroblock (Phoenix)
- Input Impedance: 10 kΩ (RCA), 20 kΩ (Euroblock)
- Maximum Input Level: 20 dBu (at 12 dBu sensitivity setting)
- Sensitivity: -10 / -2 dBV for RCA inputs, 4 / 12 dBu on Euroblock inputs
- Audio Outputs:
- Outputs: 2
- Connectors: 2-Pin Euroblock
- Integrated DSP:
- A/D and D/A Converters: 24-bit/48 kHz
- Processing Functions: Standard mixer, loudspeaker EQ, 9-band PEQ, Vpeak/Vrms limiters, delay, band-pass, mute, output polarity inversion
- Loudspeaker Presets: Flat, DS16, DS40, DS100, FS3B, 402, 802, MA12EX, RMU105, and RMU108
- Audio Latency: 1 ms (any input to speaker output)
- Indicators and Controls:
- Power LED: Solid green - On, blinking green - standby mode, solid amber - thermal fault, solid red - power supply fault
- Input Signal LED: Green - signal present, amber - the input signal is near clipping, red - signal is clipping
- Output Limit LED: Amber - the amp is limiting an output, blinking red - amp muted, solid red - indicates a fault
- Front Panel Control: Power On/Off
- Rear Panel Controls: Amplifier mode DIP switches, loudspeaker EQ dials, output attenuators
- Mains Voltage: 100 VAC - 240 VAC (+/- 10%, 50/60 Hz)
- AC Power Consumption: 79 W (Standby), 124 W (Max)
- Mains Connector: IEC 3-pin
- Maximum Inrush Current: 8.04 Amps (120 VAC / 60 Hz)
- Protection: High temperature, output short, excessively low or high AC line voltage, extra high frequency (EHF)
- Dimensions: Width - 19.0", Height - 1.750", Depth - 18.0"
- Net Weight: 12.2 lbs.
- Shipping Weight: 16.0 lbs.
- Cooling System: 2 microprocessor-controlled, variable-speed fans with the left to right airflow
The Lineup Includes:
- A wide array of FreeSpace® speakers, subwoofers, and zone amplifiers
- In-ceiling EdgeMax™ speakers for placement in corners and near walls
- Rugged, adaptable PowerShare amplifiers
- Clear, reliable Panaray® full-range driver arrays
- Versatile ControlSpace® signal processors
- Robust MB subwoofers